Opening Hour

Mon - Sun, 08:00 - 24:00

Call Us

+86-21-5838618

How to Remove Concrete Steps |

How to Remove Concrete Steps |

+

Step 4 Separate the Foundations if Needed. Make a 2 ½ inch cut in the concrete steps foundation by using a saw. Use the saw to make a line in the concrete that will serve as a weak spot easily broken apart by the sledgehammer. Next use a large sledgehammer to break up the foundation.

How to build a Homemade Wooden Bandsaw Mill from Scratch ...

How to build a Homemade Wooden Bandsaw Mill from Scratch ...

+

The first step is to make the wheels of the mill. Here we use a three quarter MDF board to make this. The wheel size is 16 inch. We use a beam compass to cut circles and cut two wheels out of them. We make a seven and half pulley for the wheel using a three quarter inch plywood and drill a five eighth inch hole into the middle where the shaft goes.

Machining the AR15 Lower Receiver Forging

Machining the AR15 Lower Receiver Forging

+

8 AR Lower Receiver StepbyStep Chapter 1 Before you start cutting on your forging, there are a some fixtures you will need to make. One is a pair of clamping pads to support and hold the forging for several setups. The other is a little drill guide that takes the heartburn out of .

How to Julienne, Dice and More: A StepByStep Guide ...

How to Julienne, Dice and More: A StepByStep Guide ...

+

Step 2: Guide Your Knife Make sure your fingers are tucked away under your hand, away from the blade. Use your knuckles to guide your knife. Tip: Peppers, carrots, leeks, celery and potatoes are ...

Building an AR15 lower receiver: A StepbyStep Visual Guide

Building an AR15 lower receiver: A StepbyStep Visual Guide

+

How to build an AR15 Lower Receiver: A Step by Step Visual Guide Building your first AR15 lower receiver can be a daunting task. I have put together a visual guide to help you easily understand the process involved in putting together your first rifle.

Install your own freefloat rail system, step by step:

Install your own freefloat rail system, step by step:

+

May 20, 2017· The two long legs of the hammer spring should rest on the top of the trigger ping installed in step 5. There is quite a bit of hammer spring tension... but squeeze the hammer into the receiver so that the hammer pin hole lines up with the holes in the lower receiver, and install the hammer pin. ... Just completed my first build, step by step ...

How to Draw a Hammer and Saw Really Easy Drawing Tutorial

How to Draw a Hammer and Saw Really Easy Drawing Tutorial

+

3. Extend two curved lines from the cheek of the hammer. This is called the neck. Connect these lines using a straight line, then extend short curved lines from each end. Connect these using another curved line to form the bell or poll of the hammer. Detail the hammer's handle, cheek, neck, and bell using curved lines of various lengths.

Step by Step Guide to Replace Ball Mill Liners | Qiming ...

Step by Step Guide to Replace Ball Mill Liners | Qiming ...

+

Step #1: Understanding the Ball mill liner. Before installing a ball mill liner initially, we need to understand it's working. In other words, we need to understand how long it will work, and if it works efficiently. Furthermore, judging the cost will also be a reasonable thing to do.

How to Julienne, Dice and More: A StepByStep Guide ...

How to Julienne, Dice and More: A StepByStep Guide ...

+

Step 2: Guide Your Knife Make sure your fingers are tucked away under your hand, away from the blade. Use your knuckles to guide your knife. Tip: Peppers, carrots, leeks, celery and potatoes are ...

8 Steps To Start a Small Edible Oil Manufacturing Business

8 Steps To Start a Small Edible Oil Manufacturing Business

+

Learn more about the business is the first step starting an oil mill company. Study the requirements of cooking oil manufacturing business in terms of technology, capital, market and competition. Visit websites such as to gain knowledge on the economic scope and statistics of .

How To Make Wood Pellets Wood Pellet Manufacture Steps ...

How To Make Wood Pellets Wood Pellet Manufacture Steps ...

+

May 13, 2016· Grinding is also a size reduction step to make wood pellet, it is a necessary step for both large and small pellet plants. During the grinding process, the raw materials will be fed into a hammer mill which will grind the raw materials into smaller pieces with a diameter under 5mm.

How To Build a Glock From an 80 Percent Frame

How To Build a Glock From an 80 Percent Frame

+

Aug 13, 2020· Install the slide assembly and perform a quick function check. Verify the slide moves through its full travel and the striker cocks. Dry fire the pistol to make sure the trigger works. Install an EMPTY magazine and retract the slide to ensure it locks to the rear. Check the slide lock to make sure it won't pull down when the slide is fully forward.

How to Use a Circular Saw Without a Table (Step by Step ...

How to Use a Circular Saw Without a Table (Step by Step ...

+

Apr 29, 2020· In this method, you'll be using a guide for the saw to make personalized cuts. Here are the step by step guidelines: 1. First, you need a pressure treated plywood or some kind of wood that is high in moisture. For that, you may have to select a circular saw blade that is made especially for plywood that is pressure treated.

How to Build a DIY Privacy Fence | Lowe's

How to Build a DIY Privacy Fence | Lowe's

+

Apr 23, 2021· Fill the bottom of the first hole with about 6 inches of dry concrete mix. Set a post on the dry concrete, flush against the layout line, but without pushing it outward. Use a post level to make sure the post is plumb and then add braces to hold it in place. Follow the same steps to .

cement mill erection step by step– Rock Crusher MillRock ...

cement mill erection step by step– Rock Crusher MillRock ...

+

Grinding Mill. grinding mills vary from coarse grinding, medium grinding to micro fine Mill(Grinder Mill)is widely used in metallurgy, building materials, chemicals, mining minerals in areas such as grinding materials materials include line, calcite, barite, coal, gypsum, mica and bentonite powder.

Power Hammer : 18 Steps Instructables

Power Hammer : 18 Steps Instructables

+

However, you can get readable drawings by downloading each step individually. Just click on the image and it will open larger in the browser. Then right click and save it to your hard drive. Once the images are on your hard drive you can enlarge them further with an image manipulation program.